Swimming pools are considered an oasis of joy and relaxation, but they need regular maintenance to look their best. Pool refinishing is a great way to restore the appearance of your pool and make it look brand new again. Depending on the extent of damage, a simple pool refinishing or you can do full-scale pool renovation to eliminate any wear and tear caused by long-term use.
Pool refinishing, or pool resurfacing, typically involves exchanging worn-out and damaged tiles and sandblasting the pool to remove any dirt or discoloration. This article will delve into the intricacies of pool resurfacing and provide an overview of the safety precautions that should apply while undertaking this task.
It would help if you did not attempt pool refinishing on your own. You should take on any pool resurfacing project only by a professional with the training and experience to handle hazardous materials and other chemicals. The refinishing process involves using dangerous acids, so always wearing protective gear while undertaking this task is important.
The time it takes to refinish a pool depends on its size. Pool refinishing can take anywhere from one to seven days. Keep the pool closed for at least a week after the completion of the refinishing project to allow any residual chemicals to dissipate safely.
Are you up to the task, still? If so, carry on reading for a few tricks and advice about resurfacing your pool all by yourself!
What are the steps in pool refinishing?
Below are the steps needed to take when refinishing your pool.
Step#1: Empty your pool
Before resurfacing your pool, the first and most important step is to drain it. Ensure you are legally allowed by checking with your local government for any required permits. You can rent a sump pump or use other methods to remove all of the water as quickly as possible. Ensure every drop has been drained and dried before continuing with this project!
Step #2: Make the surface ready.
Without a doubt, your pool has everything from debris to rust stains that need to be taken care of moving forward. Even the tiniest amount of residue could wreck any resurfacing project you had planned. After scraping away most of the mess, pressure washing should do the trick in eliminating stains, and algae stuck on your pool’s surface.
Sandblasting or chiseling the pool surface will ensure that the new material adheres properly. It is best to take it slow and complete one small area at a time; this may take up to three days! If chemical treatments are employed or if you use a sandblaster, remember to clean the pool once more before disposal of all stripped materials with a wet/dry vacuum for ultimate safety.
Before beginning priming, thoroughly check for any potential structural cracks. Seal any gaps or fissures with a pool patch specifically formulated for your pool type. When it comes to more substantial fractures, seek assistance from an experienced contractor to guarantee no underlying issues.
Step #3 Prepare the surface by priming it.
Before you begin the refinishing process, you must apply a primer epoxy to your pool’s surface. To avoid any hazardous fumes or chemicals during this step, wear protective masks and gloves while applying the product as directed on its package. Once applied across the entire area of your swimming pool, allow for two-four hours of drying time before progressing further—a timeframe that will depend upon the size of your body of water.
Step #4 Providing the surface with a finish and protection
Once the primer has had time to set, you can begin painting your pool with a topcoat epoxy or resurfacing solution. To achieve optimal results and follow the manufacturer’s instructions thoroughly, start from the deep end and work towards shallow – taking care to sand in between coats for maximum adhesion of successive layers. Generally speaking, three to four coats are required; depending on temperature conditions, this may take several hours up until overnight.
Step #5 Refill The Pool
Once you have applied the final epoxy topcoat, waiting to fill your pool with water is essential. Most manufacturers suggest letting the pool dry for five to seven days after using the last coat. After this period has passed, feel free to refill and bask in its newly rejuvenated aesthetic!
You don't have to be a hero. Call a Pool Refinishing Professional!
If you need more confidence in refinishing a pool, feel free to call any experienced professional pool resurfacing companies, like Professional Aquatic Services. With an expert on the job, you will be able to ensure the best outcome for your pool and that it is ready for use within a few days.
No matter what pool repair, renovation, or refinishing endeavor you’re embarking on – it is essential to take the necessary caution and be safe. With the right preparation and a little help from an experienced professional, your swimming pool can look as good as new in no time!
